Interface Converters
-
KD485 MODBUS RTU Library
£300.00MODBUS RTU SLAVE library for KD485-PROG. Speeds up building Modbus-custom protocol converters. No runtime royalty.
-
KD485 C Compiler
£450.00PC-based ANSI C cross-compiler for KD485-PROG, H8/300 CPU. Single user license, no runtime royalties.
-
KD485-PROG-422-20MA
£215.00 As low as: £185.25This interface converter is similar to the KD485-ADE with the addition of a 32kbyte EEPROM into which application specific data conversion programs can be loaded. It is typically used for protocol conversion applications. A MODBUS RTU SLAVE library is available to speed up the development of custom Modbus RTU converters.
Port 1 is RS422 or RS485. Port 2 is 20mA loop (TTY).
-
KD485-ADE-422-20MA
£169.00 As low as: £141.55The KD485-ADE-4XX-20MA is similar to the KD485-STD-422-20MA but inserts a microprocessor (with two serial ports) into the data path which provides data buffering and facilitates baud rate etc conversion. The RS422 or RS485 interface can operate as RS422 or 2-wire or 4-wire RS485.
Port 1 is RS422/485. Port 2 is 20mA loop (TTY).
-
KD485-STD-422-20MA
£109.00 As low as: £84.55The KD485-STD-422-20MA is an interface converter/isolator only and is baud rate and character format independent. Its main application is in isolated conversion between RS422 and 20mA loop (TTY). It requires a power supply in the range of 7-35 volts at typically less than 2 watts. If the built-in 20mA current source is to be utilised, the power supply should be 24V.
Port 1 is RS422. Port 2 is 20mA loop (TTY).
-
KD485-PROG-232-20MA
£215.00 As low as: £185.25This interface converter is similar to the KD485-ADE with the addition of a 32kbyte EEPROM into which application specific data conversion programs can be loaded. It is typically used for protocol conversion applications. A MODBUS RTU SLAVE library is available to speed up the development of custom Modbus RTU converters.
Port 1 is RS232. Port 2 is 20mA loop (TTY).
-
KD485-ADE-232-20MA
£169.00 As low as: £141.55The KD485-ADE-232-20MA is similar to the KD485-STD-232-20MA but inserts a microprocessor (with two serial ports) into the data path which provides data buffering and facilitates baud rate etc conversion. The KD485-ADE is intended for RS232 to 20mA loop (TTY), half duplex and full duplex.
Port 1 is RS232. Port 2 is 20mA loop (TTY).
-
KD485-STD-232-20MA
£109.00 As low as: £84.55The KD485-STD-232-20MA is an interface converter/isolator only and is baud rate and character format independent. Its main application is in isolated conversion between RS232 and 20mA loop (TTY). It requires a power supply in the range of 7-35 volts at typically less than 2 watts. If the built-in 20mA current source is to be utilised, the power supply should be 24V.
Port 1 is RS232. Port 2 is 20mA loop (TTY).
-
KD485-PROG-4XX-4XX
£215.00 As low as: £185.25This interface converter is similar to the KD485-ADE with the addition of a 32kbyte EEPROM into which application specific data conversion programs can be loaded. It is typically used for protocol conversion applications. A MODBUS RTU SLAVE library is available to speed up the development of custom Modbus RTU converters.
Port 1 is RS422 or RS485. Port 2 is RS422 or RS485.
-
KD485-ADE-4XX-4XX
£169.00 As low as: £141.55The KD485-ADE-4XX-4XX is similar to the KD485-STD-422-422 but inserts a microprocessor (with two serial ports) into the data path which provides data buffering and facilitates baud rate etc conversion. It can also be used for connecting 2-wire RS485 slaves to a 4-wire RS485 bus, or vice versa. Subject to minimum intermessage gaps it can also operate as a 2-wire RS485 repeater.
Port 1 is RS422 or RS485. Port 2 is RS422 or RS485.